emi filters with esd protection for data line applications CM6400a ?2010 scillc. all rights reserved. publication order number: may 2010 rev. 2 CM6400a/d product description the CM6400a is a 24-bump emi filter with esd protecti on device for data line application in a 0.4mm pitch, 5x5 csp form factor. it is fully compliant with iec 61000-4-2 level 4. the CM6400a is rohs ii compliant. electrical schematic / pin description yyww xxxx
CM6400a rev. 2 | page 2 of 8 | www.onsemi.com pin information pin descriptions a5=line 1 a4=line 2 a3=gnd a2=line 1 a1=line 2 b5=line 3 b4=line 4 b2=line 3 b1=line 4 c5=line 5 c4=line 6 c3=gnd c2=line 5 c1=line 6 d5=line 7 d4=line 8 d3=gnd d2=line 7 d1=line 8 e5=line 9 e4=line 10 e3=gnd e2=line 9 e1=line 10 ordering information part numbering information bumps package variation ordering part number 1 part marking 24 csp csp-sac105 CM6400a 64p3 note 1: parts are shipped in tape and reel form unless otherwise specified. electrical specifications and conditions parameters and operat ing conditions parameter rating units storage temperature range -55 to +150 c operating temperature range -40 to +85 c power dissipation at 70c per channel 60 mw
CM6400a rev. 2 | page 3 of 8 | www.onsemi.com electrical operat ing characteristics (see note 1) symbol parameter conditions min typ max units r resistance 100 125 150 l inductance note 2 35 nh at 1 mhz, v in = 0v; notes 2 and 3 19 24 29 pf c capacitance per channel at 1 mhz, v in = 2.5v 15 pf att(5) passband attenuation at 5mhz -7 db f c cut-off frequency z source = 50 , z load = 50 250 mhz v br breakdown voltage i r = 1ma 6 7.8 10 v i leak leakage current per channel v in = 3.0v 10 100 na v esd esd peak discharge voltage protection at all pins: a) contact discharge per iec 61000-4-2 standard b) air discharge per iec 61000-4-2 standard notes 2, 3, and 4 15 15 kv kv note 1: all parameters specified at t a = 25c unless otherwise noted. note 2: these parameters guaranteed by design. note 3: these parameters guaranteed by characterization. note 4: standard iec 61000-4-2 (c discharge = 150pf, r discharge = 330 ) .
CM6400a rev. 2 | page 4 of 8 | www.onsemi.com rf characteristics figure 1. typical insertion loss (bias=0v, t a = 25c, 50 ohm environment)
CM6400a rev. 2 | page 5 of 8 | www.onsemi.com mechanical specification csp-24 mechanical specifications the CM6400a is supplied in a 24 bump, 5x5 chip scale package (csp). package dimensions package custom csp bumps 24 millimeters inches dim min nom max min nom max a1 1.915 1.960 2.005 0.075 4 0.0772 0.0789 a2 1.915 1.960 2.005 0.075 4 0.0772 0.0789 b1 0.395 0.400 0.405 0.015 6 0.0157 0.0159 b2 0.395 0.400 0.405 0.015 6 0.0157 0.0159 c1 0.130 0.180 0.230 0.005 1 0.0071 0.0091 c2 0.130 0.180 0.230 0.005 1 0.0071 0.0091 d1 0.570 0.600 0.630 0.022 4 0.0236 0.0248 d2 0.394 0.406 0.419 0.015 5 0.0160 0.0165 controlling dimension: millimeters dimensions in millimeters package dimensions for CM6400a chip scale package
CM6400a rev. 2 | page 6 of 8 | www.onsemi.com vertical structure specification* figure 2. sectional view *daisy chain cm6000 vertical structure dimensions (nominal) ref. parameter material dimension a die thickness silicon 396 m h repassivation polyimide 10 m plated cu 7 m sputtered cu 0.4 m d ubm-(ti/cu) sputtered ti 0.1 m e ubm wetting area diameter 240 m b bump standoff 194 m f solder bump diameter after bump reflow 270 m c metal pad height alsicu 1.5 m g metal pad diameter 284 m d2 0.406mm d1 finished thickness 0.600mm
CM6400a rev. 2 | page 7 of 8 | www.onsemi.com mechanical specification (cont?d) csp tape and reel specifications part number chip size (mm) pocket size (mm) b 0 x a 0 x k 0 tape width w reel dia. qty per reel p 0 p 1 CM6400a 1.96 x 1.96 x 0.60 2.20 x 2.20 x 0.68 8mm 178mm (7") 5000 4mm 4mm + + + figure 3. tape and reel mechanical data
CM6400a rev. 2 | page 8 of 8 | www.onsemi.com revision record for nokia product datasheet CM6400a issue date details of change originator x-1 5/21/09 ? preliminary release of datasheet tim micun x-2 8/03/09 ? product name change from CM6400-p3 to CM6400a ? changed vertical structure drawing to match cm6000/cm6100 on page 4. tim micun x-3 9/15/09 ? replaced rf characteristics graph (figure 1 "typical insertion loss") on page 3. tim micun a 10/2/09 ? datasheet is now at "production" status (issue a). no other changes made. tim micun on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to make changes witho ut further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any parti cular purpose, nor does scillc assume any liability arising out of the application or use of any pr oduct or circuit, and specific ally disclaims any and all liability, including without li mitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or spec ifications can and do vary in different applications and actu al performance may vary over time. all operating parameters, including ?typicals? must be validated for each custom er application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not de signed, intended, or authorized for use as components in systems intended for surg ical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its officers , employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reason able attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303-675-2175 or 800-344-3860 toll free usa/canada fax : 303-675-2176 or 800-344-3867 toll free usa/canada email : orderlit@onsemi.com n. american technical support : 800-282-9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81-3-5773-3850 on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative
|
